Digital Logic Trainer PH-A-Q500-B-8 SA Brand

Features:
It should consist of measuring equipment such as oscilloscope (Using PC Software), waveform generator,
multi-meter, and various input/output devices that can be used for experiments of analog and digital
circuits
Basic experiments can be done intuitively by constructing basic electric and electronic circuits into
modules for practical exercises
By using AC power, Variable DC Power, Fixed Power, Variable Resistor and Analog and Digital Switch, the
circuit of bread board can be configured to use Speaker, FND, LED, etc.
Min. 2 channels of oscilloscopes and PC programs should be provided Waveform Generator which can
output Sine, Triangle and Square wave of basic 100KHz/10V (Vp-p) should be provided
8-bit output signal for easy use of digital logic circuit module and DAQ device for monitoring signal are
provided
List of Experiment:
 Module-1: Ohm’s Law: Series, parallel,
series-parallel circuit of resistance
 Module-2: Kirchhoff’s Law: Kirchhoff’s Law
of Voltage; Kirchhoff’s Law of Current
 Module-3: Law of Distribution: Law of
Voltage Distribution
 Module-4: Maximum Power Delivery:
Maximum Power Delivery Conditions
 Module-5: Thevenin and Norton’s Theorem:
Thevenin’s Theorem; Norton’s Theorem
 Module-6: Principle of Superposition:
Understanding circuit analysis method
when there are two or more current and
voltage sources
 Module-7: Loop, Node Method:
Understanding loop and node equations
with independent voltage and current
sources
 Module-8: RC Series, Parallel Circuit:
Understanding Current-Voltage
Characteristics of RC Series Circuits:
Understanding Current-Voltage
Characteristics of RC Parallel Circuits
 Module-9: RL Series, Parallel Circuit:
Understanding current-voltage
characteristics of RL series circuits;
Understanding current-voltage
characteristics of RL series circuits
 Module-10: RLC Series, Parallel Circuit:
Understanding RLC Series and Parallel
Circuits in AC; Understanding the resonance
characteristics of RLC series and parallel
circuits
 Module-11: Diode: Understanding how
diodes work; Understand voltage-current
characteristics of diodes; Understanding the
Voltage-Current Characteristics of Zener
Diodes
 Module-12: Clipper, Clamper: Understand
the operation of series and parallel clippers
and biased clippers; Understanding clamper
circuits according to diode direction
 Module-13. Rectifier Circuit: Understanding
of Half-wave, Full-wave, Bridge Full-wave
Rectifier
Filter: Understanding circuits of Low Pass
and High Pass Filters; Understanding circuits
of Band Pass and Band Stop Filters
 Hardware Specifications:
Input Parts:
AC Power: 0VAC, 3VAC, 6VAC, 9VAC,
12VAC; 3 digit 7-Segment Display (Selected
AC Power)
Variable DC Power-1: +1.5V~+18.5V; 3 digit
7-Segment Display (Output DC Power)
Variable DC Power -2:-1.5V-18.5V; 3 digit 7-
Segment Display
(Output DC Power) Analog Signal: +5V–5V
Fixed Power (DC): +20V, +15V, +5V, GND, –
5V,-15V
Slide Switch: +15V/0V Switch 2EA; +5V/0V
Switch 2EA; -5V/0V Switch 2EA; -15V/OV
Switch 2EA
Button Switch: +15V/0V Switch IEA: +5V/0V
Switch IEA: -5V/V Switch IEA; -15V/0V
Switch IEA
 Function Generator:
Waveform: Sine/Triangle/Square
DC Offset: -5V~+5V
Amplitude: 0V-10Vp-p
Frequency: 0-1kHz, 1kHz-10kHz, 10kHz-
100kHz
Duty Rate: 10-90% (Square)
Output Level: +5V TTL Level
Fixed Frequency: Output Level: +5V TTL,
Level; Frequency: 0.5Hz, 1Hz, 50Hz, 100Hz,
500Hz, 1kHz, 5kliz, 10kHz
Variable Resistor: ΙΚΩ ΙΕΑ. ΣΚΩ ΙΕΑ, 10ΚΩ
ΙΕΛ, 50ΚΩ ΙΕΛ
Select Capacitor: 100pF, InF, 10nF, 47nF,
100nF, luf
Select Inductor: 47uH, 100uH, 220uH,
470uH, 1mll, 2.2mH
Output Parts:
LED display: 5pi RED LED SEA
7-Segment Display: Anode Common 7-
Segment IEA; Cathode Common
7-Segment IEA
Speaker: 40 Speaker with Volume Control
Measurement Parts:
 Oscilloscope:
Using PC Software (USB Cable connected)
Display: 2.8inch 64K Color TFT LCD, 320×240
Pixels Resolution
Sampling Speed: 250MHz (single ch),
125MHz (dual ch)
Band Width: 70Msps/ch
Measurement Range: -30V~+30V
Voltage Division: 10mV-10V
Record Length: Max 6K samples for singlechannel; 3K samples per dual-channel
SEC/DIV Range: 5ns/div-500s/div 1, 2, 5
sequence
DC Gain Accuracy: +-3% for Normal or
Average acquisition mode,
10V/div to 10Mv/div
 Multi-Tester:
Maximum Resolution: 4000 Counts
AC/DC Voltage: Up to 600V
AC/DC Current: Up to 10A
Resistance: Up to 40ΜΩ
Capacitance: Up to 100Uf
Diode: 0-1V
 Testing Modes:
Voltage, Current, Resistance, Diode,
Capacitance
Measurement Block:
Display: 3 digit 7-Segment display
Measure Select:
Voltage/Ampere/Frequency
Voltage measure: 0-30V
Ampere measure: 0~9.99A
Frequency measure: 0Hz-5MHz
Display unit using LED
DAQ:
Using PC Software (USB Cable connected)
Sampling Speed: Ims, 10ms, 100ms Is
Input: 8 bit digital Data
Output: 8 bit TTL Level
 Waveform Generator: A/D Convertor with
8 bit output data
Power Protection Circuit:
If the circuit uses more than the allowable
current for short-circuit reasons, shutoff the
power
When the temperature inside the
equipment is over a certain temperature
(70°C), the power is cut off
LED indicates the location of the power
source that is problematic when Beep
sound when power off the power is off
LED informs the status of power
connection/operation/short
Power can be switched on/off using a
switch